No products in the cart.

Product was successfully added to your shopping cart.

5

Product was successfully added to your compare list.

5

Product was successfully added to your wishlist.

5

The BF-1610 CO2 laser machine offers economical solution for general purpose cutting and engraving on acrylics, cardboard, wood, textile, laminates, stone, and other materials.

$17,000.00

* Required Fields

$17,000.00
+
-

SKU: BF1610

Large Working Area

The BF-1610 has a working area of 63" x 39" (1600mm x 1000mm) in an X Y dimension. With an easily opened front door and back component, the BF-1610 has a rear pass through functionality. Users can easily process long work pieces, and feature a better dust exhaust result by closing the front door and back components when processing a work piece inside the working area.

The aluminum strip table is used for hard and non-flammable material processing for materials such as acrylic, cardboard and wood, in order to avoid laser reflection and garner a clean cutting edge.

Deep Collecting Bay and Picking Up Drawer

After processing, small parts and parts without a supporting strip under them drop down into the deep collecting bay to avoid interaction with the laser. Users can easily remove them by pulling out the drawer.

High Performance Motion System

High Performance Motion System

Using servo motors from internationally known suppliers, the BF-1610 moves quickly at an extremely high resolution with a step length of 6.35μm (4000DPI), and an acceleration of 0.2G for cutting, and 2G for engraving. Users can also choose a more economical model with high quality step motors without sacrificing performance.

Laser Source

Laser Source

The BF-1610 can be equipped with dual 100W, 130W, or 150W glass CO2 laser tubes with an outstanding cost performance ratio according to your needs. Users can use either one or both at the same time by pressing the laser power enable button on the control panel.

Our 150W laser can cut acrylic up to 1-1/8" (30mm), which is the best available on the market.

Industrial Chiller

Industrial Chiller

The BF-1610 is equipped with a high quality industrial chiller to ensure the continuous and stable output of the laser.

Laser Head

Laser Head

The BF-1610 is equipped with dual heads according to laser configuration. Users can easily adjust the space between the two heads.

Our laser head has 2 installation positions for the focus lens, with the same focusing space between the nozzle and the workpiece. The lower position if for 2.5" and general purpose processing. The upper position is for 4" and cutting purposes.

The reflection mirror adjustment is designed to be stable and easy to use. With 3 adjustment screws, it is easy to align in any condition.

The BF-1610 is also equipped with an air assist assembly with a flow adjustment on the laser head. By directing a steady stream of compressed air across the cutting surface, the possibility of flaming, scorching or charring is reduced when cutting materials such as acrylic or wood.

High Quality Optics

High Quality Optics

The BF-1610 is equipped with optics produced in America in order to produce a high quality and consistent laser beam across the entire working area. This achieves a better cutting and engraving quality.

Visual Control System

Visual Control System

The BF-1610 is equipped with a high performance control system featuring a user friendly visual UI panel. By embedding flash storage in the controller, users can transfer jobs through a USB drive, Ethernet, or flash disk, then finish the processing offline without relying on a computer connection. With a true color TFT LCD panel, users can also preview machine status and job details before processing, such as the current position of the laser head, connection status, graphic detail, processing parameters and estimated processing time. Users can also adjust the parameters for different materials, as well as run a processing simulation on the panel. The control system will save all changes made for future use. While processing, users will receive real time processing information on the panel, and can adjust parameters on the fly according to actual results. In the event of power failure or mistakes, users can recover the job.

Software and Print Driver

Software and Print Driver

Uses can import or create a new design, finish layout and sorting, run a processing simulation and directly control the machine using our software.

With the user friendly print driver, users can also use their favorite applications, such as CorelDRAW, Photoshop, or AutoCAD to transfer a job to the machine through a few simple clicks. With layers and a color mapping function, users can assign different processing parameters for different colors in a design. There is no need to run separate jobs for one project, and processing is faster with a more precise laser control.

Included Exhaust Blower

Included Exhaust Blower

We provide a ready to use laser cutting and engraving machine package with all necessary parts, including the exhaust blower. Simply set up the machine and start the project.

Safety and Reliability

The BF-1610 is designed, engineered and built with safety and reliability in mind. We use electronic parts from internationally known suppliers and build a system to meet international standards. There are numerous sensors around the machine, such as an open door sensor, open laser tube box sensors, laser cooling water pressure sensor and more. The machine will stop automatically if something unsafe occurs, and users can shut down the machine immediately and completely by pressing the easy to reach emergency stop button on the panel.

GU Eagle Introduction

Come to G.U. Eagle for all your laser cutting and engraving needs, and join the ranks of companies like Disney for quality laser cutting machines!

Subscribe